View previous topic :: View next topic |
Author |
Message |
GAS
Joined: 02 Jul 2018 Posts: 39 Location: Hoover Al
|
Posted: Sun Mar 03, 2024 4:51 pm Post subject: What is a good way to put dents in a plastic body? Firefly? |
|
|
What is a good way to put dents in a plastic body? Hair dryer does not have enough heat. Open flame is too hot. I tried a soldering iron. Worked OK at first. The long shaft on the iron gets hot also and makes it hard to heat one small place. Internet showed someone using incense. I do not know if it would be hot enough. Looked like you could pit point the heat, if it is hot enough. If this does not work at least the room would smell good. I may try a thin aluminum can. Looks like this would be hard to get the lines correct. Any suggestions would be appreciated. Thanks |
|
Back to top |
|
|
TN Vols fan
Joined: 18 Jan 2022 Posts: 286 Location: Crossett, AR
|
Posted: Sun Mar 03, 2024 6:52 pm Post subject: |
|
|
You could maybe try a heat gun? Mine has two settings. I don't remember the exact settings as far as temps go, but one is significantly higher than the other. I've never tried it on a body. _________________ "Many men fish all their lives without knowing it is not the fish they are after." Henry David Thoreau
"I am, Sir, a brother of the angle" quote from The Compleat Angler, lzzak Walton 1654 |
|
Back to top |
|
|
jh63fan
Joined: 10 Sep 2021 Posts: 362 Location: Tarheel State
|
Posted: Sun Mar 03, 2024 8:24 pm Post subject: |
|
|
Soda can is a little too thick for that. Seen several times where people use heavy duty aluminium foil, burnish over the body panel to make a copy, then replace the panel and inflict the damage. Also heard of using embossing tin or foil, but haven't seen that finished. |
|
Back to top |
|
|
TonyK
Joined: 21 Feb 2018 Posts: 116
|
Posted: Mon Mar 04, 2024 7:32 am Post subject: |
|
|
I've always used a candle. You can move the model around above it to control the heat. Then I use assorted things like pliers, a screwdriver, some type of blunt tool to make the dents. Lots of patience to get the results. |
|
Back to top |
|
|
Vdc
Joined: 04 Sep 2022 Posts: 132
|
Posted: Mon Mar 04, 2024 11:58 am Post subject: |
|
|
You can sand the bodyshell from inside?
A thinner guage plastic would deform quicker.
If you burn through, you could repair from the inside and perhaps the dent atea edges would look sharper too. More scale correct. |
|
Back to top |
|
|
Crime Dog
Joined: 27 Jan 2018 Posts: 339
|
Posted: Mon Mar 04, 2024 5:04 pm Post subject: |
|
|
You can try brake checking Ross Chastain or Kyle Busch!
Actually the methods mentioned above see to work pretty well. |
|
Back to top |
|
|
Firefly
Joined: 28 Jan 2018 Posts: 813 Location: New Jersey
|
Posted: Mon Mar 04, 2024 8:59 pm Post subject: |
|
|
The best way to get convincing bent metal? Use metal.
This was done with an aluminum diet coke can:
The hood is actually the original resin, though - but since it was a pretty clean crease, I just scored and bent it a bit.
Some pieces were done with wine bottle foil.
Can aluminum is a bit brittle but the thickness is scale accurate. Trace a panel, cut with snips, bend with needle nose pliers or whatever - take practice, but at least the material is cheap! _________________ Bill Jobson is my real name. |
|
Back to top |
|
|
George Andrews
Joined: 30 Jan 2018 Posts: 460
|
Posted: Mon Mar 04, 2024 9:09 pm Post subject: |
|
|
Crime Dog wrote: | You can try brake checking Ross Chastain or Kyle Busch!
Actually the methods mentioned above see to work pretty well. |
If you have an Industrial Supply house nearby, ask for 10 / thousands thickness Stainless Steel SHIM STOCK. It's not cheap, but one roll will last a lifetime. You will find many uses for this, including interior panels. |
|
Back to top |
|
|
GAS
Joined: 02 Jul 2018 Posts: 39 Location: Hoover Al
|
Posted: Thu Mar 07, 2024 10:18 pm Post subject: Dents in plastic body |
|
|
Thanks for all the suggestions. While I work on the interior, I will think about how to do this. I am leaning on Firefly's thoughts. Since his model turned out so well, I may be using soft drink can. Any thoughts on how to hang the aluminum to the plastic (epoxy and bondo)? |
|
Back to top |
|
|
Firefly
Joined: 28 Jan 2018 Posts: 813 Location: New Jersey
|
Posted: Sun Mar 10, 2024 8:55 am Post subject: Re: Dents in plastic body |
|
|
GAS wrote: | ... I may be using soft drink can. Any thoughts on how to hang the aluminum to the plastic (epoxy and bondo)? |
I used two part epoxy. (the general liquidy kind)
A note about can aluminum - it will be brittle - so working a crease back and forth can crack it apart. That was a challenge with the Montego's sharply creased fender edges. I did reinforce some pieces from behind them with a little Tamiya epoxy putty. Good luck! _________________ Bill Jobson is my real name. |
|
Back to top |
|
|
|